Installing a USB Weather Station on a Raspberry PI Part 1

One of the reasons for having multiple PI’s was to have one take over duties from an aging ITX based Linux box of reading from a USB Weather station and uploading the data to both it’s website and WeatherUnderground.

Unfortunately this project got pushed forward when, last Thursday morning, the ITX box decided to die on me. I think it’s power supply finally gave out after 9 years of service.

So this is the first part of a series on setting up a USB weather station onto a Raspberry PI.
Continue reading “Installing a USB Weather Station on a Raspberry PI Part 1”

The EU & Space Weather monitoring

Whilst doing my daily read through Hansard on the train is morning I came across this written answer in the House of Lords about monitoring Space Weather:

Asked by Lord Hunt of Chesterton

To ask Her Majesty’s Government what plans they have, in collaboration with other European countries and the European Space Agency, to establish a European system for monitoring, forecasting and disseminating information on space weather. [HL839]

The Parliamentary Under-Secretary of State, Department for Business, Innovation and Skills (Baroness Wilcox): The UK Space Agency is working with the European Space Agency (ESA) to develop a space situational awareness programme. An element of this programme covers the development of operational space weather monitoring facilities, including space borne instruments, ground based sensors and telescopes. A further element of the programme addresses the provision and dissemination of space weather forecasts and event warnings by setting up a pilot space weather service centre with expert advisers, a support helpdesk, an archive and a web portal.

This is an optional ESA programme and UK participation must be subject to review against other calls on the space agency budget. A draft business case supporting participation has been prepared by agency staff in consultation with the UK space weather community and interested stakeholders.

© Parliamentary material is reproduced with the permission of the Controller of HMSO on behalf of Parliament. Licence No: P2011000006

Getting GPS to work on a Raspberry PI

One of the tasks I want to use a Raspberry PI for is to take over the duties of an existing ITX based linux box running my weather station. Now in theory that should be pretty simple as the current setup uses pywws to connect to the station and as that’s written in python it should work.

Now the Raspberry PI has no onboard Real time clock – which means it needs to use an NTP server to get the time when it starts. Usually you would use the default settings and allow the PI to connect to thenet for it’s time. Now this is fine if you have a working net connection but what if you are not connected to the net? You might be in the field running the PI on batteries.

As the other projects I have lined up for it is to connect my Meade LX200GPS telescope to the local network or to work with my (in prototype) radio telescopes so having an accurate clock is going to be required.

Now the obvious solution here is to use GPS as a time source. GPS works by having a constellation of satellites in orbit and each one carries a highly accurate atomic clock & broadcast both their current position and the time. A GPS receiver then receives these signals and, as long as it has enough satellites and workout where you are by comparing the times from those clocks.

So this article shows how to use A GPS receiver with the Rasperry PI – although these instructions are not specific to the PI.

The hardware

For this experiment I’m using a USB GPS receiver from Maplin – product code A73KF. I bought this several months ago when they had it on special offer for £19.99 – it usually retails for £29.99.

Raspberry PI with the A73KF GPS receiver plugged in

Now it comes with a CD for Windows machines but we don’t need it – as the majority of GPS receivers I know of use serial & this is no exception. When plugged in it appears as a serial port.

Plug it in and run lsusb

pi@raspberrypi:~$ sudo lsusb
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

There the Prolific Technology entry is the GPS appearing as a serial port. If you look in /var/log/syslog you will also notice it will have created the port as /dev/ttyUSB0 as it’s the first serial port.

Using the PI as a GPS Receiver

Now the next step is to get the pi receiving data from the satellites. Now there is a suite of tools available for Linux called gpsd which we’ll install:

pi@raspberrypi:~$ sudo apt-get install gpsd gpsd-clients python-gps

Next we need to start the daemon:

pi@raspberrypi:~$ sudo gpsd /dev/ttyUSB0 -F /var/run/gpsd.sock

Ignore any messages from the console or in the log files, you may see it complaining about IPv6 but you can ignore that.

Viewing whats in the sky & your location

Now GPS doesn’t work indoors – as it needs a clear view of the sky so for this I’ve placed the PI on the window sill. Next I ssh into the pi and run cgps.

pi@raspberrypi:~$ cgps -s

The -s flag is there to tell the command not to write raw data to the screen as well as the processed data.

You should then get the following output:

│    Time:       2012-06-18T15:05:10.0Z     ││PRN:   Elev:  Azim:  SNR:  Used: │
│    Latitude:    51.231848 N               ││  14    43    249    40      Y   │
│    Longitude:    0.514014 E               ││  25    75    283    37      Y   │
│    Altitude:   132.3 m                    ││   2    26    085    31      Y   │
│    Speed:      0.0 kph                    ││  12    56    070    18      Y   │
│    Heading:    0.0 deg (true)             ││   9    19    133    22      Y   │
│    Climb:      0.0 m/min                  ││  27    09    133    17      Y   │
│    Status:     3D FIX (1 secs)            ││   4    17    045    31      Y   │
│    GPS Type:                              ││  32    05    321    20      Y   │
│    Longitude Err:   +/- 8 m               ││  29    41    192    18      Y   │
│    Latitude Err:    +/- 9 m               ││  31    28    304    42      Y   │
│    Altitude Err:    +/- 27 m              ││                                 │
│    Course Err:      n/a                   ││                                 │
│    Speed Err:       +/- 68 kph            ││                                 │
│                                           ││                                 │
│                                           ││                                 │
│                                           ││                                 │
│                                           ││                                 │
│                                           ││                                 │

Here you can see it’s receiving from 10 satellites and it has the time and your location. The 3D FIX section tells you it has enough data for a 3D fix on your location (i.e. altitude). The Err lines tell you the error in your position. If you leave it running you should see the Err values change every second or so.

Viewing GPS under X-Windows

Now above I showed how the GPS looks from an SSH connection but you can get a graphical display as well using the xgps client thats also been installed. Now if you have a monitor connected to the pi simply open a terminal and run xgps. However as I’ve not got a monitor against the window I’ve used ssh to connect to it from another machine. To get this to work you need to add -Y to the ssh command.

peter@somehost:~ $ ssh -Y pi@raspberrypi
pi@raspberrypi:~$ xgps

You should now get a window like the following open on your local machine – don’t worry if it takes a little while, it might take a second or two:

xgps running on a PI but being displayed on Mac OS-X

Setting the computer time using GPS

Now we have a working GPS we can now get the PI to use it for setting the time. To do this we need to configure ntp to use the GPS satellites as a time source. Now you should already have ntp installed but if not then you need to install it:

pi@raspberrypi:~$ sudo apt-get install ntp

Next you need to edit the file: /etc/ntp.conf and add a few lines to it defining the GPS. This can be either before or after the existing lines beginning with server:

# gps ntp
server minpoll 4
fudge time1 0.183 refid NMEA
server minpoll 4 prefer
fudge refid PPS

Now restart ntp:

pi@raspberrypi:~$ sudo service ntp restart

Now if you query the server you should after a while see it synchronize:

pi@raspberrypi:~$ ntpq -p
remote           refid      st t when poll reach   delay   offset  jitter
*    2 u   54   64    7   65.454    2.666   5.800
+resntp-b-vip.lo    3 u   45   64   17   55.704   -5.169   8.482
+bart.nexellent.   2 u   17   64   17   76.585   -4.271  57.595   2 u   20   64   37   86.464   -2.374 228.460
xSHM(0)          .NMEA.           0 l   11   16  377    0.000  144.714   3.026
SHM(1)          .PPS.            0 l    -   16    0    0.000    0.000   0.000

A couple of notes:

You might find that ntp doesn’t connect to the gps at first. It appears that it starts gpsd up without the link to the serial port. What I find I have to do is:

pi@raspberrypi:~$ sudo killall gpsd
pi@raspberrypi:~$ sudo gpsd /dev/ttyUSB0 -F /var/run/gpsd.sock
pi@raspberrypi:~$ sudo service ntp restart

Once I’ve done this then after it gets a fix then it starts working. Sometimes running cgps and waiting for it to get a fix also fixes this.

I don’t know why this happens but it’s an issue I’ve yet to solve.